p2vr做的网站怎么再次打开,买过域名之前就可以做网站了吗,西安app软件开发公司,产品开发流程的六个阶段是实验要求
该项目主要实现一个深度为8、位宽为8bit的同步FIFO存储单元。模块功能应包括读控制、写控制、同时读写控制、FIFO满状态、FIFO空状态等逻辑部分。 该项目由一个功能模块和一个testbench组成。其中功能模块的端口信号如下表所示。 提示#xff1a; #xff08;1 1设定一个写地址waddr[2:0]每来一个写使能wr则写地址加一 2设定一个读地址raddr[2:0]每来一个读使能rd则读地址加一 3若同时读写则读写地址不变只是将输入数据din直接赋值给dout; 4FIFO中数据的个数coutwaddr-raddr; 5状态指示
当cout8时FIFO满full1;当cout6时FIFO快满了almost_full1;当cout4时FIFO半满半空half1;当cout2时FIFO快空了almost_empty1;当cout0时FIFO空empty1;
sfifo
module sfifo(clk,rst_n,data_in,wr,rd,full,empty,data_out,sfifo_cnt,half,almost_empty,almost_full);input clk;input rst_n;input [7:0] data_in;input wr;input rd;output full;output empty;output almost_full;output almost_empty;output half;output [7:0] data_out;output [3:0] sfifo_cnt;wire clk;wire rst_n;wire [7:0] data_in;wire wr;wire rd;wire full;wire empty;wire almost_full;wire almost_empty;wire half;reg [7:0] data_out;reg [3:0] sfifo_cnt;define DEL 1 // Clock-to-output delayreg [7:0] sfifo_ram[0:7]; // sfifo_ram initializedreg [2:0] rd_ptr; // Read pointerreg [2:0] wr_ptr; // Write pointer assign empty ( sfifo_cnt 0 ) ? 1 : 0; //Empty signalassign full ( sfifo_cnt 8 ) ? 1 : 0; //Full signalassign almost_full ( sfifo_cnt 6 ) ? 1 : 0; //Almost Full signalassign almost_empty ( sfifo_cnt 2 ) ? 1 : 0;//Almost Empty signalassign half ( sfifo_cnt 4 ) ? 1 : 0;//HALF signal// sfifo_cnt changed// 当读有效, cnt--// 当写有效, cntalways ( posedge clk or negedge rst_n) beginif( ~rst_n ) beginsfifo_cnt #DEL 4h0;endelse if( rd ~wr ) beginsfifo_cnt #DEL sfifo_cnt - 1;endelse if( ~rd wr ) beginsfifo_cnt #DEL sfifo_cnt 1;endelse begin sfifo_cnt sfifo_cnt;endend always ( posedge clk or negedge rst_n) beginif( ~rst_n ) beginrd_ptr #DEL 3h0;endelse if( rd ) beginif( rd_ptr 3h7 ) beginrd_ptr #DEL 3h0;endelse beginrd_ptr #DEL rd_ptr 1;endendelse beginrd_ptr rd_ptr;endend always ( posedge clk or negedge rst_n) beginif( ~rst_n ) beginwr_ptr #DEL 3h0;endelse if( wr ) beginif( wr_ptr 3h7 ) beginwr_ptr #DEL 3h0;endelse beginwr_ptr #DEL wr_ptr 1;endendelse beginwr_ptr wr_ptr;endend always ( posedge clk or negedge rst_n) beginif( ~rst_n ) begindata_out #DEL 8h0;endelse if( wr ) beginsfifo_ram[wr_ptr] #DEL data_in;endelse if( rd ) begin data_out #DEL sfifo_ram[rd_ptr];endend endmodule sfifo_test
module sfifo_test();reg clk;reg rst_n;reg [7:0] data_in;reg wr;reg rd;wire full;wire empty;wire almost_full;wire almost_empty;wire half;wire [7:0] data_out;wire [3:0] sfifo_cnt;initial beginrst_n1;clk0;wr0;rd0;data_in0;#1 rst_n0;#5 rst_n1;#3 wr1;#5 rd1;#5 rd0;#5 wr0;#5 wr1;#10 rd1;#10 rd0;endalways begin#5 clk~clk;endalways (posedge clk or negedge rst_n) beginif (~rst_n) begindata_in0;wr0;rd0;endelse begindata_in$random;endendinitial begin$dumpfile (F:/Robei/practice/prac_07_sfifo/sfifo_test.vcd);$dumpvars;#5000;$stop;end//---Module instantiation---sfifo sfifo1(.clk(clk),.rst_n(rst_n),.data_in(data_in),.wr(wr),.rd(rd),.full(full),.empty(empty),.almost_full(almost_full),.almost_empty(almost_empty),.half(half),.data_out(data_out),.sfifo_cnt(sfifo_cnt));endmodule 实验结果
整体波形 读 写 同时读写
