临海响应式网站设计,wordpress 视频网站,网上申请入团网站,石桥铺网站建设公司1.开发板配置
本人开发板使用ESP32S3-wroom1-n16r8最小系统板
由于基于vscode与PlatformIO框架开发#xff0c;无espidf框架#xff0c;因此无法直接烧录程序#xff0c;配置开发板参数如下#xff1a; 在platformio.ini文件中#xff0c;配置使用esp32-s3-devkitc-1开发…1.开发板配置
本人开发板使用ESP32S3-wroom1-n16r8最小系统板
由于基于vscode与PlatformIO框架开发无espidf框架因此无法直接烧录程序配置开发板参数如下 在platformio.ini文件中配置使用esp32-s3-devkitc-1开发板型号自行指定flash和psram运行模式启用psram并指定大小开启串口调试即可 [env:esp32s3_wroom]
platform espressif32
board esp32-s3-devkitc-1 ; 使用N16版本的板型
framework arduinoboard_build.arduino.partitions default_16MB.csv
; 指定FLASH和PSRAM的运行模式
board_build.arduino.memory_type qio_opi
; 指定FLASH容量为16MB
board_upload.flash_size 16MB
upload_speed 921600
upload_port COM17 ; 根据实际端口修改
monitor_speed 115200
build_flags -DBOARD_HAS_PSRAM ; 启用PSRAM-DPSRAM_SIZE8 ; 指定8MB PSRAM-DARDUINO_USB_MODE1 开启串口调试-DARDUINO_USB_CDC_ON_BOOT1-DARDUINO_RUNNING_CORE1-DARDUINO_EVENT_RUNNING_CORE1lib_deps bodmer/TFT_eSPI^2.5.43moononournation/GFX Library for Arduino^1.5.4 主要博文VS Codeplatformio配置ESP32-S3-N16R88MB PSRAM 16MB FLASH工程 - Macrored - 博客园
2.安装GFX显示屏库
直接搜索gfx下滑即可选择加入到工程文件中 之后选择自己的工程文件夹添加即可
3.修改配置文件
打开该目录基于个人开发板可能文件目录不同将PDQ文件夹下所有h文件复制到主文件夹下main.cpp同级目录 4.之后修改其中两个文件开启esp32s3 rgb配置 5.修改配置引脚
在第四步同一文件夹下修改配置spi引脚 之后根据自身显示屏尺寸外形选择对应rgb引脚配置函数我使用的为2寸方形屏幕因此使用option4 之后根据实际硬件接线修改该函数下引脚配置 Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,10 /* R0 */, 9 /* R1 */, 8 /* R2 */, 7 /* R3 */, 6 /* R4 */,5 /* G0 */, 4 /* G1 */, 3 /* G2 */, 2 /* G3 */, 1 /* G4 */, 17 /* G5 */,40 /* B0 */, 39 /* B1 */, 38 /* B2 */, 47 /* B3 */, 45 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 640 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type11_init_operations, sizeof(st7701_type11_init_operations)); 屏幕引脚序号屏幕引脚定义esp32s3引脚序号1leda3.3引脚可拉高2ledkgnd3vcc3.3拉高4gnggnd5gnggnd6gnggnd7gnggnd8gnggnd9gnggnd10gnggnd11gnggnd12gnggnd13gnggnd14vs1215hs1116pclk1417de1318b04019b13920b23821b34722b44523g0524g1425g2326g3227g4128g51729r01030r1931r2832r3733r4634rest46屏幕初始化19引脚不可用35cs1536scl1637sda2138gndgnd39vcc3.3拉高 3.3拉高引脚20 19 18
此时特别注意屏幕中RESET引脚后续修改屏幕底层驱动时不同厂家屏幕屏幕底层驱动初始化需要RESET引脚电平触发。
6.修改屏幕分辨率
根据自身购买屏幕分辨率修改对应参数 7.修改屏幕初始化函数需要商家提供资料
打开屏幕初始化函数 根据自身屏幕驱动资料修改对应寄存器配置内容该函数中不可调用延时等函数用宏定义即可商家屏幕部分驱动资料 RST即为屏幕的RESET引脚如需配置电平初始化在屏幕启动函数之前单独配置电平即可延时函数推荐使用微秒级延时函数。
之后根据商家资料更改每个指令中寄存器配置内容注意com与dat不同函数区别。 main.cpp中step函数配置RESET引脚即可 8.配置主函数
主函数中配置对应指令烧录程序即可。 9.注意事项
1.打开开发板的PSRAM功能并配置
2.如果出现竖状彩色条纹花屏检查以下配置内容 显示屏初始化函数 st7701_type11_init_operations 显示屏底层驱动中寄存器配置 显示屏分辨率引脚配置 显示屏初始化引脚RESET引脚
3.注意显示屏模式rgb656还是rgb888涉及显示屏初始化驱动函数内容修改 10.附上相关文件代码
main.cpp
#include Arduino_GFX_Library.h
#include Arduino_GFX_dev_device.h
/*
#include Arduino_DataBus.h
#include Arduino_G.h
#include Arduino_GFX.h
#include Arduino_TFT.h
#include Arduino_TFT_18bit.h
#include YCbCr2RGB.h
#include gfxfont.h
*/// 使用extern声明外部变量
//extern Arduino_DataBus *bus; // 声明外部数据总线
//extern Arduino_ESP32RGBPanel *rgbpanel; // 声明外部RGB面板
//extern Arduino_RGB_Display *gfx; // 声明外部RGB显示对象const int RESET46; //定义屏幕复位引脚涉及屏幕初始化
void setup() {Serial.begin(115200);Serial.println(ESP32-S3 启动);Serial.println(初始化GPIO引脚...);pinMode(20, OUTPUT); pinMode(18, OUTPUT); pinMode(48, OUTPUT); digitalWrite(20, HIGH);digitalWrite(18, HIGH);digitalWrite(48,HIGH);Serial.println(GPIO引脚初始化完成);Serial.println(开始初始化显示屏...);//显示屏初始化 RST引脚配置pinMode(RESET, OUTPUT);digitalWrite(RESET, HIGH); delayMicroseconds(1000); digitalWrite(RESET, LOW); delayMicroseconds(5000);digitalWrite(RESET, HIGH); delayMicroseconds(50000);if (!gfx-begin()) {Serial.println(显示屏初始化失败!);} else {Serial.println(显示屏初始化成功!);}// 初始化显示gfx-fillScreen(WHITE);delay(1000);
}void loop() {gfx-fillScreen(RED);delay(1000);gfx-fillScreen(GREEN);delay(1000);gfx-fillScreen(BLUE);delay(1000);gfx-drawCircle(250, 250, 50, RED); Serial.println(ok); // 在屏幕中心画圆delay(1000);/* gfx-fillCircle(240, 240, 40, GREEN); // 填充圆delay(1000);gfx-drawRect(190, 190, 100, 100, BLUE); // 画矩形delay(1000); */
}
platformIO.ini [env:esp32s3_wroom]
platform espressif32
board esp32-s3-devkitc-1 ; 使用N16版本的板型
framework arduinoboard_build.arduino.partitions default_16MB.csv
; 指定FLASH和PSRAM的运行模式
board_build.arduino.memory_type qio_opi
; 指定FLASH容量为16MB
board_upload.flash_size 16MB
upload_speed 921600
upload_port COM17 ; 根据实际端口修改
monitor_speed 115200
build_flags -DBOARD_HAS_PSRAM ; 启用PSRAM-DPSRAM_SIZE8 ; 指定8MB PSRAM-DARDUINO_USB_MODE1-DARDUINO_USB_CDC_ON_BOOT1-DARDUINO_RUNNING_CORE1-DARDUINO_EVENT_RUNNING_CORE1lib_deps bodmer/TFT_eSPI^2.5.43moononournation/GFX Library for Arduino^1.5.4屏幕初始化底层驱动函数Arduino_RGB_Display.h文件中
static const uint8_t st7701_type11_init_operations[] {BEGIN_WRITE,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,WRITE_COMMAND_8, 0xEF,WRITE_BYTES, 1, 0x08,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x10,WRITE_C8_D16, 0xC0, 0x4F, 0x00,WRITE_C8_D16, 0xC1, 0x11, 0x0C,WRITE_C8_D16, 0xC2, 0x07, 0x0A,WRITE_COMMAND_8, 0xC3,WRITE_BYTES, 3, 0x83, 0x33, 0x1B,//WRITE_C8_D8, 0xCC, 0x10, // changed by manufactureWRITE_COMMAND_8, 0xB0, // Positive Voltage Gamma ControlWRITE_BYTES, 16,0x00, 0x0F, 0x18, 0x0D,0x12, 0x07, 0x05, 0x08,0x07, 0x21, 0x30, 0x10,0x0F, 0x26, 0x2F, 0x1F,WRITE_COMMAND_8, 0xB1, // Negative Voltage Gamma ControlWRITE_BYTES, 16,0x00, 0x1B, 0x20, 0x0C,0x0E, 0x03, 0x08, 0x08,0x08, 0x22, 0x05, 0x11,0x0F, 0x2A, 0x32, 0x1F,// PAGE1WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x11,WRITE_C8_D8, 0xB0, 0x35, // Vop4.7375vWRITE_C8_D8, 0xB1, 0x52, // VCOM32WRITE_C8_D8, 0xB2, 0x81, // VGH15vWRITE_C8_D8, 0xB3, 0x80,WRITE_C8_D8, 0xB5, 0x4E, // VGL-10.17vWRITE_C8_D8, 0xB7, 0x85,WRITE_C8_D8, 0xB8, 0x21, // AVDD6.6 AVCL-4.6WRITE_C8_D8, 0xC0, 0x09,WRITE_C8_D8, 0xC1, 0x78,WRITE_C8_D8, 0xC2, 0x78,WRITE_C8_D8, 0xD0, 0x88,WRITE_COMMAND_8, 0xE0,WRITE_BYTES, 3, 0x00, 0xA0, 0x02,WRITE_COMMAND_8, 0xE1,WRITE_BYTES, 11,0x06, 0xA0, 0x08, 0xA0,0x05, 0xA0, 0x07, 0xA0,0x00, 0x44, 0x44,WRITE_COMMAND_8, 0xE2,WRITE_BYTES, 13,0x20, 0x20, 0x40, 0x40,0x96, 0xA0, 0x00, 0x00,0x96, 0xA0, 0x00, 0x00,0x00,WRITE_COMMAND_8, 0xE3,WRITE_BYTES, 4, 0x00, 0x00, 0x22, 0x22,WRITE_C8_D16, 0xE4, 0x44, 0x44,WRITE_COMMAND_8, 0xE5,WRITE_BYTES, 16,0x0E, 0x97, 0x10, 0xA0,0x10, 0x99, 0x10, 0xA0,0x0A, 0x93, 0x10, 0xA0,0x0C, 0x95, 0x10, 0xA0,WRITE_COMMAND_8, 0xE6,WRITE_BYTES, 4, 0x00, 0x00, 0x22, 0x22,WRITE_C8_D16, 0xE7, 0x44, 0x44,WRITE_COMMAND_8, 0xE8,WRITE_BYTES, 16,0x0D, 0x96, 0x10, 0xA0,0x0F, 0x98, 0x10, 0xA0,0x09, 0x92, 0x10, 0xA0,0x0B, 0x94, 0x10, 0xA0,WRITE_COMMAND_8, 0xEB,WRITE_BYTES, 7,0x00, 0x01, 0x4E, 0x4E,0x44, 0x88, 0x40,WRITE_C8_D16, 0xEC, 0x78, 0x00,WRITE_COMMAND_8, 0xED,WRITE_BYTES, 16,0xFF, 0xFA, 0x2F, 0x89,0x76, 0x54, 0x01, 0xFF,0xFF, 0x10, 0x45, 0x67,0x98, 0xF2, 0xAF, 0xFF,//-----------VAP VAN---------------WRITE_COMMAND_8, 0xEF,WRITE_BYTES, 6, 0x08, 0x08, 0x08, 0x45, 0x3F,0x54,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,WRITE_COMMAND_8, 0xE8,WRITE_BYTES, 8, 0x00, 0x0E, 0xFF, 0x77, 0x01, 0x00, 0x00, 0x00,WRITE_COMMAND_8, 0x11,// Sleep OutEND_WRITE,DELAY, 120,BEGIN_WRITE,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,WRITE_COMMAND_8, 0xE8,WRITE_BYTES, 2, 0x00, 0x0C,END_WRITE,DELAY, 10,BEGIN_WRITE,WRITE_COMMAND_8, 0xE8,WRITE_BYTES, 2, 0x00, 0x00,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x00,WRITE_COMMAND_8, 0x3A,WRITE_BYTES, 1, 0x55, // RGB565// WRITE_BYTES, 1, 0x77, // RGB888WRITE_COMMAND_8, 0x29, // Display OnWRITE_BYTES, 1, 0x00,END_WRITE};// Init code for 480x480 round TL021WVC02 display
static const uint8_t TL021WVC02_init_operations[] {BEGIN_WRITE,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x10,WRITE_C8_D16, 0xC0, 0x3B, 0x00,WRITE_C8_D16, 0xC1, 0x0B, 0x02, // VBPWRITE_C8_D16, 0xC2, 0x00, 0x02,WRITE_C8_D8, 0xCC, 0x10,WRITE_C8_D8, 0xCD, 0x08,WRITE_COMMAND_8, 0xB0, // Positive Voltage Gamma ControlWRITE_BYTES, 16,0x02, 0x13, 0x1B, 0x0D,0x10, 0x05, 0x08, 0x07,0x07, 0x24, 0x04, 0x11,0x0E, 0x2C, 0x33, 0x1D,WRITE_COMMAND_8, 0xB1, // Negative Voltage Gamma ControlWRITE_BYTES, 16,0x05, 0x13, 0x1B, 0x0D,0x11, 0x05, 0x08, 0x07,0x07, 0x24, 0x04, 0x11,0x0E, 0x2C, 0x33, 0x1D,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x11,WRITE_C8_D8, 0xB0, 0x5d, // 5dWRITE_C8_D8, 0xB1, 0x43, // VCOM amplitude settingWRITE_C8_D8, 0xB2, 0x81, // VGH Voltage setting, 12VWRITE_C8_D8, 0xB3, 0x80,WRITE_C8_D8, 0xB5, 0x43, // VGL Voltage setting, -8.3VWRITE_C8_D8, 0xB7, 0x85,WRITE_C8_D8, 0xB8, 0x20,WRITE_C8_D8, 0xC1, 0x78,WRITE_C8_D8, 0xC2, 0x78,WRITE_C8_D8, 0xD0, 0x88,WRITE_COMMAND_8, 0xE0,WRITE_BYTES, 3, 0x00, 0x00, 0x02,WRITE_COMMAND_8, 0xE1,WRITE_BYTES, 11,0x03, 0xA0, 0x00, 0x00,0x04, 0xA0, 0x00, 0x00,0x00, 0x20, 0x20,WRITE_COMMAND_8, 0xE2,WRITE_BYTES, 13,0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00,0x00,WRITE_COMMAND_8, 0xE3,WRITE_BYTES, 4, 0x00, 0x00, 0x11, 0x00,WRITE_C8_D16, 0xE4, 0x22, 0x00,WRITE_COMMAND_8, 0xE5,WRITE_BYTES, 16,0x05, 0xEC, 0xA0, 0xA0,0x07, 0xEE, 0xA0, 0xA0,0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00,WRITE_COMMAND_8, 0xE6,WRITE_BYTES, 4, 0x00, 0x00, 0x11, 0x00,WRITE_C8_D16, 0xE7, 0x22, 0x00,WRITE_COMMAND_8, 0xE8,WRITE_BYTES, 16,0x06, 0xED, 0xA0, 0xA0,0x08, 0xEF, 0xA0, 0xA0,0x00, 0x00, 0x00, 0x00,0x00, 0x00, 0x00, 0x00,WRITE_COMMAND_8, 0xEB,WRITE_BYTES, 7,0x00, 0x00, 0x40, 0x40,0x00, 0x00, 0x00,WRITE_COMMAND_8, 0xED,WRITE_BYTES, 16,0xFF, 0xFF, 0xFF, 0xBA,0x0A, 0xBF, 0x45, 0xFF,0xFF, 0x54, 0xFB, 0xA0,0xAB, 0xFF, 0xFF, 0xFF,WRITE_COMMAND_8, 0xEF,WRITE_BYTES, 6,0x10, 0x0D, 0x04, 0x08,0x3F, 0x1F,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x13,WRITE_C8_D8, 0xEF, 0x08,WRITE_COMMAND_8, 0xFF,WRITE_BYTES, 5, 0x77, 0x01, 0x00, 0x00, 0x00,WRITE_C8_D8, 0x36, 0x00,WRITE_C8_D8, 0x3A, 0x60, // 0x70 RGB888, 0x60 RGB666, 0x50 RGB565WRITE_COMMAND_8, 0x11, // Sleep OutEND_WRITE,DELAY, 100,BEGIN_WRITE,WRITE_COMMAND_8, 0x29, // Display OnEND_WRITE,DELAY, 50};
Arduino-GFX-dev-devich.h文件
// #define AD35_S3
// #define BLOCKCODELAB_ARCADE_LITE
// #define DLC35010R // or called Elecrow ESP Terminal with 3.5inch Parallel RGB Capacitive Touch Display (ILI9488)
// #define DRAGON_RADAR
// #define ESP32_1732S019
// #define ESP32_2424012
// #define ESP32_2432S028
// #define ESP32_3248S035
// #define ESP32_4827A043 /* requires manual set bus speed to 8 mHz: gfx-begin(8000000) */
// #define ESP32_4827A043_QSPI
// #define ESP32_4827S043
// #define ESP32_4848S040_86BOX_GUITION
// #define ESP32_8048S043
// #define ESP32_8048S070
// #define ESP32_LCDKIT_SPI
// #define ESP32_LCDKIT_PAR8A
// #define ESP32_LCDKIT_PAR8B
// #define ESP32_LCDKIT_PAR16
// #define ESP32_S3_313LCD
// #define ESP32_S3_BOX_3
// #define ESP32_S3_EYE#define ESP32_S3_RGB
// #define ESP32_S3_RPI_DPI
// #define ESP32S3_2_1_TP
// #define GS_T3E // Golden Security GS-T3E
// #define IBUBLY
// #define JC1060P470
// #define JC3248W535
// #define JC3636W518
// #define LILYGO_T_DECK
// #define LILYGO_T_DECK_PLUS
// #define LILYGO_T_DISPLAY
// #define LILYGO_T_DISPLAY_S3
// #define LILYGO_T_Display_S3_AMOLED
// #define LILYGO_T_Display_S3_AMOLED_1_64
// #define LILYGO_T_Display_S3_LONG
// #define LILYGO_T_DISPLAY_S3_PRO
// #define LILYGO_T_QT
// #define LILYGO_T_RGB
// #define LILYGO_T_TRACK
// #define LILYGO_T_WATCH_2021
// #define LILYGO_T4_S3
// #define MAKERFABS_TFT_TOUCH_3_5
// #define MAKERFABS_ESP32_S3_TFT_4_0
// #define MAKERFABS_ESP32_S3_TFT_4_3_v1_3
// #define WT32_SC01
// #define XIAO_SAMD21_ROUND_DISPLAY
// #define XIAO_ESP32C3_ROUND_DISPLAY
// #define XIAO_ESP32S3_ROUND_DISPLAY
// #define WAVESHARE_ESP32_S3_LCD_2_8
// #define WAVESHARE_RP2040_LCD_0_96
// #define WZ8048C050 // or called Elecrow Wizee-ESP32
// #define ZX2D10GE10R_V4848
// #define ZX3D50CE02S // or called WT32-SC01 PLUS
// #define ZX3D95CE01S_AR
// #define ZX3D95CE01S_TR
// #define ZX7D00CE01S // or called QM Smart Panlee 7.0 inch serial screen#if defined(AD35_S3)
#define GFX_DEV_DEVICE AD35_S3
#include Wire.h
#include Adafruit_AW9523.h
Adafruit_AW9523 aw;
#define DEV_DEVICE_INIT() \{ \Wire.begin(6 /* SDA */, 5 /* SCL */); \aw.begin(0x59); \aw.pinMode(8, OUTPUT); /* LCD_LEDK */ \aw.pinMode(9, OUTPUT); /* LCD_LEDK */ \aw.pinMode(10, OUTPUT); /* LCD_LEDK */ \aw.pinMode(11, OUTPUT); /* LCD_LEDK */ \aw.pinMode(14, OUTPUT); /* LCD_RST */ \aw.digitalWrite(8, LOW); /* LCD_LEDK */ \aw.digitalWrite(9, LOW); /* LCD_LEDK */ \aw.digitalWrite(10, LOW); /* LCD_LEDK */ \aw.digitalWrite(11, LOW); /* LCD_LEDK */ \aw.digitalWrite(14, HIGH); /* LCD_RST */ \}
Arduino_DataBus *bus new Arduino_ESP32LCD8(45 /* DC */, GFX_NOT_DEFINED /* CS */, 10 /* WR */, GFX_NOT_DEFINED /* RD */,9 /* D0 */, 4 /* D1 */, 3 /* D2 */, 8 /* D3 */, 18 /* D4 */, 17 /* D5 */, 16 /* D6 */, 15 /* D7 */);
Arduino_GFX *gfx new Arduino_ST7796(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(BLOCKCODELAB_ARCADE_LITE)
#define GFX_DEV_DEVICE BLOCKCODELAB_ARCADE_LITE
#define GFX_BL 21
Arduino_DataBus *bus new Arduino_ESP32SPI(45 /* DC */, 10 /* CS */, 12 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */, HSPI /* spi_num */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, 46 /* RST */, 3 /* rotation */, false /* IPS */);#elif defined(DLC35010R)
#define GFX_DEV_DEVICE DLC35010R
#define GFX_BL 46
Arduino_DataBus *bus new Arduino_ESP32PAR16(45 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, 48 /* RD */,47 /* D0 */, 21 /* D1 */, 14 /* D2 */, 13 /* D3 */, 12 /* D4 */, 11 /* D5 */, 10 /* D6 */, 9 /* D7 */,3 /* D8 */, 8 /* D9 */, 16 /* D10 */, 15 /* D11 */, 7 /* D12 */, 6 /* D13 */, 5 /* D14 */, 4 /* D15 */);
Arduino_GFX *gfx new Arduino_ILI9488(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, false /* IPS */);#elif defined(DRAGON_RADAR)
#define GFX_DEV_DEVICE DRAGON_RADAR
#define GFX_BL 38
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 39 /* CS */,48 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,11 /* R0 */, 12 /* R1 */, 13 /* R2 */, 45 /* R3 */, 0 /* R4 */,8 /* G0 */, 19 /* G1 */, 20 /* G2 */, 46 /* G3 */, 9 /* G4 */, 10 /* G5 */,4 /* B0 */, 5 /* B1 */, 6 /* B2 */, 7 /* B3 */, 15 /* B4 */,1 /* hsync_polarity */, 50 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 30 /* hsync_back_porch */,1 /* vsync_polarity */, 20 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 30 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type6_init_operations, sizeof(st7701_type6_init_operations));#elif defined(ESP32_1732S019)
#define GFX_DEV_DEVICE ESP32_1732S019
#define GFX_BL 14
Arduino_DataBus *bus new Arduino_ESP32SPI(11 /* DC */, 10 /* CS */, 12 /* SCK */, 13 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, 1 /* RST */, 0 /* rotation */, true /* IPS */, 170 /* width */, 320 /* height */, 35 /* col offset 1 */, 0 /* row offset 1 */, 35 /* col offset 2 */, 0 /* row offset 2 */);#elif defined(ESP32_2424012)
#define GFX_DEV_DEVICE ESP32_2424012
#define GFX_BL 8
Arduino_DataBus *bus new Arduino_ESP32SPI(2 /* DC */, 10 /* CS */, 6 /* SCK */, 7 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(ESP32_2432S028)
#define GFX_DEV_DEVICE ESP32_2432S028
#define GFX_BL 21
Arduino_DataBus *bus new Arduino_ESP32SPI(2 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, 12 /* MISO */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */);#elif defined(ESP32_3248S035)
#define GFX_DEV_DEVICE ESP32_3248S035
#define GFX_BL 27
Arduino_DataBus *bus new Arduino_ESP32SPI(2 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, 12 /* MISO */, VSPI /* spi_num */);
Arduino_GFX *gfx new Arduino_ST7796(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */);#elif defined(ESP32_4827A043)
#define GFX_DEV_DEVICE ESP32_4827A043
#define GFX_BL 2
Arduino_DataBus *bus new Arduino_ESP32LCD16(48 /* DC */, 45 /* CS */, 47 /* WR */, 21 /* RD */,5 /* D0 */, 6 /* D1 */, 7 /* D2 */, 15 /* D3 */, 16 /* D4 */, 4 /* D5 */, 8 /* D6 */, 3 /* D7 */,46 /* D8 */, 9 /* D9 */, 1 /* D10 */, 42 /* D11 */, 39 /* D12 */, 41 /* D13 */, 40 /* D14 */, 14 /* D15 */);
Arduino_GFX *gfx new Arduino_NV3041A(bus, 17 /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(ESP32_4827A043_QSPI)
#define GFX_DEV_DEVICE ESP32_4827A043_QSPI
#define GFX_BL 1
Arduino_DataBus *bus new Arduino_ESP32QSPI(45 /* CS */, 47 /* SCK */, 21 /* D0 */, 48 /* D1 */, 40 /* D2 */, 39 /* D3 */);
Arduino_GFX *gfx new Arduino_NV3041A(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(ESP32_4827S043)
#define GFX_DEV_DEVICE ESP32_4827S043
#define GFX_BL 2
#define RGB_PANEL
// option 1:
// Uncomment for ILI6485 LCD 480x272
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,0 /* hsync_polarity */, 1 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 43 /* hsync_back_porch */,0 /* vsync_polarity */, 3 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 12 /* vsync_back_porch */,1 /* pclk_active_neg */, 10000000 /* prefer_speed */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 272 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);
// option 2:
// Uncomment for ST7262 IPS LCD 800x480
// Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(
// 40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
// 45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
// 5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
// 8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
// 0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 8 /* hsync_back_porch */,
// 0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 8 /* vsync_back_porch */,
// 1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
// Arduino_RGB_Display *gfx new Arduino_RGB_Display(
// 800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);
// option 3:
// Uncomment for RPi DPI 1024x600
// Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(
// 40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,
// 45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,
// 5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,
// 8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,
// 0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 43 /* hsync_back_porch */,
// 0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 12 /* vsync_back_porch */,
// 1 /* pclk_active_neg */, 9000000 /* prefer_speed */);
// Arduino_RGB_Display *gfx new Arduino_RGB_Display(
// 1024 /* width */, 600 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);/* 4.0 86BOX from GUITION ESP32-4848S040 display */
#elif defined(ESP32_4848S040_86BOX_GUITION)
#define GFX_DEV_DEVICE ESP32_4848S040_86BOX_GUITION
#define GFX_BL 38
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 39 /* CS */,48 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,11 /* R0 */, 12 /* R1 */, 13 /* R2 */, 14 /* R3 */, 0 /* R4 */,8 /* G0 */, 20 /* G1 */, 3 /* G2 */, 46 /* G3 */, 9 /* G4 */, 10 /* G5 */,4 /* B0 */, 5 /* B1 */, 6 /* B2 */, 7 /* B3 */, 15 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 1 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type9_init_operations, sizeof(st7701_type9_init_operations));#elif defined(ESP32_8048S043)
#define GFX_DEV_DEVICE ESP32_8048S043
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 8 /* hsync_back_porch */,0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 8 /* vsync_back_porch */,1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);#elif defined(ESP32_8048S070)
#define GFX_DEV_DEVICE ESP32_8048S070
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(41 /* DE */, 40 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,14 /* R0 */, 21 /* R1 */, 47 /* R2 */, 48 /* R3 */, 45 /* R4 */,9 /* G0 */, 46 /* G1 */, 3 /* G2 */, 8 /* G3 */, 16 /* G4 */, 1 /* G5 */,15 /* B0 */, 7 /* B1 */, 6 /* B2 */, 5 /* B3 */, 4 /* B4 */,0 /* hsync_polarity */, 180 /* hsync_front_porch */, 30 /* hsync_pulse_width */, 16 /* hsync_back_porch */,0 /* vsync_polarity */, 12 /* vsync_front_porch */, 13 /* vsync_pulse_width */, 10 /* vsync_back_porch */,1 /* pclk_active_neg */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);#elif defined(ESP32_LCDKIT_SPI)
#define GFX_DEV_DEVICE ESP32_LCDKIT_SPI
#define GFX_BL 23
Arduino_DataBus *bus new Arduino_ESP32SPI(19 /* DC */, 5 /* CS */, 22 /* SCK */, 21 /* MOSI */, 27 /* MISO */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, 18 /* RST */, 1 /* rotation */);#elif defined(ESP32_LCDKIT_PAR8A)
#define GFX_DEV_DEVICE ESP32_LCDKIT_PAR8A
Arduino_DataBus *bus new Arduino_ESP32PAR8(5 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, GFX_NOT_DEFINED /* RD */, 19 /* D0 */, 21 /* D1 */, 0 /* D2 */, 22 /* D3 */, 23 /* D4 */, 33 /* D5 */, 32 /* D6 */, 27 /* D7 */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);#elif defined(ESP32_LCDKIT_PAR8B)
#define GFX_DEV_DEVICE ESP32_LCDKIT_PAR8B
Arduino_DataBus *bus new Arduino_ESP32PAR8(5 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, GFX_NOT_DEFINED /* RD */, 25 /* D0 */, 26 /* D1 */, 12 /* D2 */, 13 /* D3 */, 14 /* D4 */, 15 /* D5 */, 2 /* D6 */, 4 /* D7 */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);#elif defined(ESP32_LCDKIT_PAR16)
#define GFX_DEV_DEVICE ESP32_LCDKIT_PAR16
Arduino_DataBus *bus new Arduino_ESP32PAR16(5 /* DC */, GFX_NOT_DEFINED /* CS */, 18 /* WR */, GFX_NOT_DEFINED /* RD */,19 /* D0 */, 21 /* D1 */, 0 /* D2 */, 22 /* D3 */, 23 /* D4 */, 33 /* D5 */, 32 /* D6 */, 27 /* D7 */,25 /* D8 */, 26 /* D9 */, 12 /* D10 */, 13 /* D11 */, 14 /* D12 */, 15 /* D13 */, 2 /* D14 */, 4 /* D15 */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);#elif defined(ESP32_S3_313LCD)
#define GFX_DEV_DEVICE ESP32_S3_313LCD
#define GFX_BL 4
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 0 /* CS */,17 /* SCK */, 16 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(15 /* DE */, 5 /* VSYNC */, 6 /* HSYNC */, 7 /* PCLK */,19 /* R0 */, 8 /* R1 */, 18 /* R2 */, 17 /* R3 */, 16 /* R4 */,11 /* G0 */, 10 /* G1 */, 9 /* G2 */, 46 /* G3 */, 3 /* G4 */, 20 /* G5 */,47 /* B0 */, 21 /* B1 */, 14 /* B2 */, 13 /* B3 */, 12 /* B4 */,1 /* hsync_polarity */, 30 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 30 /* hsync_back_porch */,1 /* vsync_polarity */, 16 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 16 /* vsync_back_porch */,0 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(376 /* width */, 960 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, gc9503v_type2_init_operations, sizeof(gc9503v_type2_init_operations));#elif defined(ESP32_S3_BOX_3)
#define GFX_DEV_DEVICE ARDUINO_ESP32_S3_BOX_3
#define GFX_BL 47
Arduino_DataBus *bus new Arduino_ESP32SPI(4 /* DC */, 5 /* CS */, 7 /* SCK */, 6 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ILI9342(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */);#elif defined(ESP32_S3_EYE)
#define GFX_DEV_DEVICE ESP32_S3_EYE
#define DEV_DEVICE_INIT() \{ \pinMode(3 /* camera indicator */, OUTPUT); \digitalWrite(3 /* camera indicator */, LOW); \pinMode(48 /* BACKLIGHT */, OUTPUT); \digitalWrite(48 /* BACKLIGHT */, LOW); \}
Arduino_DataBus *bus new Arduino_ESP32SPI(43 /* DC */, 44 /* CS */, 21 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */, 240 /* width */, 240 /* height */, 0 /* col offset 1 */, 0 /* row offset 1 */, 0 /* col offset 2 */, 80 /* row offset 2 */);#elif defined(ESP32_S3_RGB)
#define GFX_DEV_DEVICE ESP32_S3_RGB
// #define GFX_BL 38
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 15 /* CS */,16 /* SCK */, 21 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
// option 1:
// Uncomment for 4 rect display //Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(// 13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,// 10 /* R0 */, 9 /* R1 */, 8 /* R2 */, 7 /* R3 */, 6 /* R4 */,// 5 /* G0 */, 4 /* G1 */, 3 /* G2 */, 2 /* G3 */, 1 /* G4 */, 17 /* G5 */,// 40 /* B0 */, 39 /* B1 */, 38 /* B2 */, 47 /* B3 */, 45 /* B4 */,// 0 /* hsync_polarity */, 80 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 80 /* hsync_back_porch */,// 0 /* vsync_polarity */, 18 /* vsync_front_porch */, 2 /* vsync_pulse_width */, 30 /* vsync_back_porch */, 0 /* pclk_active_neg */, 6000000L /* pclk_frequency */);//Arduino_RGB_Display *gfx new Arduino_RGB_Display(
// 240 /* width */, 320 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
// bus, 46 /* RST */, st7701_type10_init_operations, sizeof(st7701_type10_init_operations));// option 2:
// Uncomment for 2.1 round display
// Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(
// 18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
// 4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
// 10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
// 15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
// 1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,
// 1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
// Arduino_RGB_Display *gfx new Arduino_RGB_Display(
// 480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
// bus, GFX_NOT_DEFINED /* RST */, st7701_type5_init_operations, sizeof(st7701_type5_init_operations));// option 3:
// Uncomment for 2.8 round display
// Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(
// 18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
// 4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
// 10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
// 15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
// 1 /* hsync_polarity */, 50 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 30 /* hsync_back_porch */,
// 1 /* vsync_polarity */, 20 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 30 /* vsync_back_porch */);
// Arduino_RGB_Display *gfx new Arduino_RGB_Display(
// 480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
// bus, GFX_NOT_DEFINED /* RST */, st7701_type6_init_operations, sizeof(st7701_type6_init_operations));// option 4:
// Uncomment for 2.0 displayArduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,10 /* R0 */, 9 /* R1 */, 8 /* R2 */, 7 /* R3 */, 6 /* R4 */,5 /* G0 */, 4 /* G1 */, 3 /* G2 */, 2 /* G3 */, 1 /* G4 */, 17 /* G5 */,40 /* B0 */, 39 /* B1 */, 38 /* B2 */, 47 /* B3 */, 45 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 640 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type11_init_operations, sizeof(st7701_type11_init_operations));// option 5:
// Uncomment for 3.5 display
// Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(
// 18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,
// 4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,
// 10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,
// 15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,
// 1 /* hsync_polarity */, 20 /* hsync_front_porch */, 30 /* hsync_pulse_width */, 38 /* hsync_back_porch */,
// 1 /* vsync_polarity */, 4 /* vsync_front_porch */, 3 /* vsync_pulse_width */, 15 /* vsync_back_porch */,
// 10 /* pclk_active_neg */, 16000000 /* prefer_speed */);
// Arduino_RGB_Display *gfx new Arduino_RGB_Display(
// 640 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,
// bus, GFX_NOT_DEFINED /* RST */, st7701_type1_init_operations, sizeof(st7701_type1_init_operations));#elif defined(ESP32_S3_RPI_DPI)
#define GFX_DEV_DEVICE ESP32_S3_RPI_DPI
// #define GFX_BL 38#define RGB_PANEL
// e.g. Waveshare 7 RPi DPI LCD: https://www.waveshare.com/wiki/7inch_LCD_for_Pi
// dpi_timings1024 1 40 48 128 600 1 13 3 45 0 0 0 60 0 37000000 6
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,4 /* R0 */, 3 /* R1 */, 2 /* R2 */, 1 /* R3 */, 0 /* R4 */,10 /* G0 */, 9 /* G1 */, 8 /* G2 */, 7 /* G3 */, 6 /* G4 */, 5 /* G5 */,15 /* B0 */, 14 /* B1 */, 13 /* B2 */, 12 /* B3 */, 11 /* B4 */,1 /* hsync_polarity */, 40 /* hsync_front_porch */, 48 /* hsync_pulse_width */, 128 /* hsync_back_porch */,1 /* vsync_polarity */, 13 /* vsync_front_porch */, 3 /* vsync_pulse_width */, 45 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(1024 /* width */, 600 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);#elif defined(ESP32S3_2_1_TP)
#define GFX_DEV_DEVICE ESP32S3_2_1_TP
#define GFX_BL 38
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 39 /* CS */,48 /* SCK */, 47 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(18 /* DE */, 17 /* VSYNC */, 16 /* HSYNC */, 21 /* PCLK */,4 /* R0 */, 5 /* R1 */, 6 /* R2 */, 7 /* R3 */, 15 /* R4 */,8 /* G0 */, 20 /* G1 */, 3 /* G2 */, 46 /* G3 */, 9 /* G4 */, 10 /* G5 */,11 /* B0 */, 12 /* B1 */, 13 /* B2 */, 14 /* B3 */, 0 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type5_init_operations, sizeof(st7701_type5_init_operations));/* Golden Security GS-T3E */
#elif defined(GS_T3E)
#define GFX_DEV_DEVICE GS_T3E
#define GFX_BL 42
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 4 /* CS */,15 /* SCK */, 48 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(40 /* DE */, 39 /* VSYNC */, 38 /* HSYNC */, 41 /* PCLK */,8 /* R0 */, 18 /* R1 */, 17 /* R2 */, 16 /* R3 */, 0 /* R4 */,13 /* G0 */, 12 /* G1 */, 11 /* G2 */, 10 /* G3 */, 9 /* G4 */, 3 /* G5 */,15 /* B0 */, 48 /* B1 */, 47 /* B2 */, 21 /* B3 */, 14 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, 4 /* RST */, st7701_type1_init_operations, sizeof(st7701_type1_init_operations));#elif defined(IBUBLY)
#define GFX_DEV_DEVICE IBUBLY
#define GFX_BL 17 // default backlight pin, you may replace DF_GFX_BL to actual backlight pin
Arduino_DataBus *bus new Arduino_ESP32SPI(8 /* DC */, 9 /* CS */, 10 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, 12 /* RST */, 1 /* rotation */, true /* IPS */, 240 /* width */, 280 /* height */, 0 /* col offset 1 */, 20 /* row offset 1 */, 0 /* col offset 2 */, 20 /* row offset 2 */);#elif defined(JC1060P470)
#define GFX_DEV_DEVICE JC1060P470
#define GFX_BL 23 // default backlight pin, you may replace DF_GFX_BL to actual backlight pin
#define DSI_PANEL
Arduino_ESP32DSIPanel *dsipanel new Arduino_ESP32DSIPanel(40 /* hsync_pulse_width */, 160 /* hsync_back_porch */, 160 /* hsync_front_porch */,10 /* vsync_pulse_width */, 23 /*vsync_back_porch */, 12 /* vsync_front_porch */,48000000 /* prefer_speed */);
Arduino_DSI_Display *gfx new Arduino_DSI_Display(1024 /* width */, 600 /* height */, dsipanel, 0 /* rotation */, true /* auto_flush */,27 /* RST */, jd9165_init_operations, sizeof(jd9165_init_operations) / sizeof(lcd_init_cmd_t));#elif defined(JC3248W535)
#define GFX_DEV_DEVICE JC3248W535
#define GFX_BL 1
Arduino_DataBus *bus new Arduino_ESP32QSPI(45 /* CS */, 47 /* SCK */, 21 /* D0 */, 48 /* D1 */, 40 /* D2 */, 39 /* D3 */);
Arduino_GFX *g new Arduino_AXS15231B(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, false /* IPS */, 320 /* width */, 480 /* height */);
#define CANVAS
Arduino_Canvas *gfx new Arduino_Canvas(320 /* width */, 480 /* height */, g, 0 /* output_x */, 0 /* output_y */, 0 /* rotation */);#elif defined(JC3636W518)
#define GFX_DEV_DEVICE JC3636W518
#define GFX_BL 15
Arduino_DataBus *bus new Arduino_ESP32QSPI(10 /* CS */, 9 /* SCK */, 11 /* D0 */, 12 /* D1 */, 13 /* D2 */, 14 /* D3 */);
Arduino_GFX *gfx new Arduino_ST77916(bus, 47 /* RST */, 0 /* rotation */, true /* IPS */, 360 /* width */, 360 /* height */);#elif defined(LILYGO_T_DECK)
#define GFX_DEV_DEVICE LILYGO_T_DECK
#define DEV_DEVICE_INIT() \{ \pinMode(9 /* TDECK_RADIO_CS */, OUTPUT); \digitalWrite(9 /* TDECK_RADIO_CS */, HIGH); \pinMode(12 /* TDECK_LCD_CS */, OUTPUT); \digitalWrite(12 /* TDECK_LCD_CS */, HIGH); \pinMode(39 /* TDECK_SDCARD_CS */, OUTPUT); \digitalWrite(39 /* TDECK_SDCARD_CS */, HIGH); \pinMode(10 /* TDECK_PERI_POWERON */, OUTPUT); \digitalWrite(10 /* TDECK_PERI_POWERON */, HIGH); \delay(500); \}
#define GFX_BL 42
Arduino_DataBus *bus new Arduino_HWSPI(11 /* DC */, 12 /* CS */, 40 /* SCK */, 41 /* MOSI */, 38 /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */, false /* IPS */);#elif defined(LILYGO_T_DECK_PLUS)
#define GFX_DEV_DEVICE LILYGO_T_DECK_PLUS
#define DEV_DEVICE_INIT() \{ \pinMode(9 /* TDECK_RADIO_CS */, OUTPUT); \digitalWrite(9 /* TDECK_RADIO_CS */, HIGH); \pinMode(12 /* TDECK_LCD_CS */, OUTPUT); \digitalWrite(12 /* TDECK_LCD_CS */, HIGH); \pinMode(39 /* TDECK_SDCARD_CS */, OUTPUT); \digitalWrite(39 /* TDECK_SDCARD_CS */, HIGH); \pinMode(10 /* TDECK_PERI_POWERON */, OUTPUT); \digitalWrite(10 /* TDECK_PERI_POWERON */, HIGH); \delay(500); \}
#define GFX_BL 42
Arduino_DataBus *bus new Arduino_HWSPI(11 /* DC */, 12 /* CS */, 40 /* SCK */, 41 /* MOSI */, 38 /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */, false /* IPS */);#elif defined(LILYGO_T_DISPLAY)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY
#define GFX_BL 4
Arduino_DataBus *bus new Arduino_ESP32SPI(16 /* DC */, 5 /* CS */, 18 /* SCK */, 19 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, 23 /* RST */, 0 /* rotation */, true /* IPS */, 135 /* width */, 240 /* height */, 52 /* col offset 1 */, 40 /* row offset 1 */, 53 /* col offset 2 */, 40 /* row offset 2 */);#elif defined(LILYGO_T_DISPLAY_S3)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3
#define DEV_DEVICE_INIT() \{ \pinMode(15 /* PWD */, OUTPUT); \digitalWrite(15 /* PWD */, HIGH); \}
#define GFX_BL 38
Arduino_DataBus *bus new Arduino_ESP32PAR8Q(7 /* DC */, 6 /* CS */, 8 /* WR */, 9 /* RD */,39 /* D0 */, 40 /* D1 */, 41 /* D2 */, 42 /* D3 */, 45 /* D4 */, 46 /* D5 */, 47 /* D6 */, 48 /* D7 */);
Arduino_GFX *gfx new Arduino_ST7789(bus, 5 /* RST */, 0 /* rotation */, true /* IPS */, 170 /* width */, 320 /* height */, 35 /* col offset 1 */, 0 /* row offset 1 */, 35 /* col offset 2 */, 0 /* row offset 2 */);#elif defined(LILYGO_T_Display_S3_AMOLED)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_AMOLED
Arduino_DataBus *bus new Arduino_ESP32QSPI(6 /* CS */, 47 /* SCK */, 18 /* D0 */, 7 /* D1 */, 48 /* D2 */, 5 /* D3 */);
Arduino_GFX *gfx new Arduino_RM67162(bus, 17 /* RST */, 0 /* rotation */);#elif defined(LILYGO_T_Display_S3_AMOLED_1_64)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_AMOLED_1_64
#define DEV_DEVICE_INIT() \{ \pinMode(16 /* LCD_EN */, OUTPUT); \digitalWrite(16 /* LCD_EN */, HIGH); \}
Arduino_DataBus *bus new Arduino_ESP32QSPI(10 /* CS */, 12 /* SCK */, 11 /* D0 */, 13 /* D1 */, 14 /* D2 */, 15 /* D3 */);
Arduino_GFX *g new Arduino_CO5300(bus, 17 /* RST */, 0 /* rotation */, false /* IPS */, 280, 456,20 /* col offset 1 */, 0 /* row offset 1 */, 180 /* col_offset2 */, 24 /* row_offset2 */);
#define CANVAS
Arduino_Canvas *gfx new Arduino_Canvas(280 /* width */, 456 /* height */, g, 0 /* output_x */, 0 /* output_y */, 0 /* rotation */);#elif defined(LILYGO_T_Display_S3_LONG)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_LONG
#define GFX_BL 1
Arduino_DataBus *bus new Arduino_ESP32QSPI(12 /* CS */, 17 /* SCK */, 13 /* D0 */, 18 /* D1 */, 21 /* D2 */, 14 /* D3 */);
Arduino_GFX *g new Arduino_AXS15231B(bus, 47 /* RST */, 0 /* rotation */, false /* IPS */, 180 /* width */, 640 /* height */);
#define CANVAS
Arduino_Canvas *gfx new Arduino_Canvas(180 /* width */, 640 /* height */, g, 0 /* output_x */, 0 /* output_y */, 0 /* rotation */);#elif defined(LILYGO_T_DISPLAY_S3_PRO)
#define GFX_DEV_DEVICE LILYGO_T_DISPLAY_S3_PRO
#define GFX_BL 48
Arduino_DataBus *bus new Arduino_ESP32SPI(9 /* DC */, 39 /* CS */, 18 /* SCK */, 17 /* MOSI */, 8 /* MISO */);
Arduino_GFX *gfx new Arduino_ST7796(bus, 47 /* RST */, 0 /* rotation */, true /* IPS */, 222 /* width */, 480 /* height */, 49 /* col offset 1 */, 0 /* row offset 1 */, 49 /* col offset 2 */, 0 /* row offset 2 */);#elif defined(LILYGO_T_QT)
#define GFX_DEV_DEVICE LILYGO_T_QT
#define DEV_DEVICE_INIT() \{ \pinMode(10 /* BL */, OUTPUT); \digitalWrite(10 /* BL */, LOW); \}
Arduino_DataBus *bus new Arduino_ESP32SPI(6 /* DC */, 5 /* CS */, 3 /* SCK */, 2 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_GC9107(bus, 1 /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(LILYGO_T_RGB)
#define GFX_DEV_DEVICE LILYGO_T_RGB
#include Wire.h
#define DEV_DEVICE_INIT() \{ \Wire.begin(8 /* SDA */, 48 /* SCL */, 800000L /* speed */); \}
#define GFX_BL 46
Arduino_DataBus *bus new Arduino_XL9535SWSPI(8 /* SDA */, 48 /* SCL */, 2 /* XL PWD */, 3 /* XL CS */, 5 /* XL SCK */, 4 /* XL MOSI */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(45 /* DE */, 41 /* VSYNC */, 47 /* HSYNC */, 42 /* PCLK */,21 /* R0 */, 18 /* R1 */, 17 /* R2 */, 16 /* R3 */, 15 /* R4 */,14 /* G0 */, 13 /* G1 */, 12 /* G2 */, 11 /* G3 */, 10 /* G4 */, 9 /* G5 */,7 /* B0 */, 6 /* B1 */, 5 /* B2 */, 3 /* B3 */, 2 /* B4 */,1 /* hsync_polarity */, 50 /* hsync_front_porch */, 1 /* hsync_pulse_width */, 30 /* hsync_back_porch */,1 /* vsync_polarity */, 20 /* vsync_front_porch */, 1 /* vsync_pulse_width */, 30 /* vsync_back_porch */,1 /* pclk_active_neg */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type4_init_operations, sizeof(st7701_type4_init_operations));#elif defined(LILYGO_T_TRACK)
#define GFX_DEV_DEVICE LILYGO_T_TRACK
#define DEV_DEVICE_INIT() \{ \pinMode(4 /* POWER */, OUTPUT); \digitalWrite(4 /* POWER */, HIGH); \}
Arduino_DataBus *bus new Arduino_ESP32SPIDMA(7 /* DC */, 9 /* CS */, 5 /* SCK */, 6 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_G *g new Arduino_JD9613(bus, 8 /* RST */);
#define CANVAS
Arduino_Canvas *gfx new Arduino_Canvas(126 /* width */, 294 /* height */, g, 0, 0, 3);#elif defined(LILYGO_T_WATCH_2021)
#define GFX_DEV_DEVICE LILYGO_T_WATCH_2021
#define GFX_BL 21
Arduino_DataBus *bus new Arduino_ESP32SPI(19 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_GC9A01(bus, 27 /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(LILYGO_T4_S3)
#define GFX_DEV_DEVICE LILYGO_T4_S3
#define DEV_DEVICE_INIT() \{ \pinMode(9 /* POWER */, OUTPUT); \digitalWrite(9 /* POWER */, HIGH); \}
Arduino_DataBus *bus new Arduino_ESP32QSPI(11 /* CS */, 15 /* SCK */, 14 /* D0 */, 10 /* D1 */, 16 /* D2 */, 12 /* D3 */);
Arduino_GFX *g new Arduino_RM690B0(bus, 13 /* RST */, 0 /* rotation */, 450 /* width */, 600 /* height */, 16 /* col offset 1 */, 0 /* row offset 1 */, 16 /* col offset 2 */, 0 /* row offset 2 */);
#define CANVAS
Arduino_Canvas *gfx new Arduino_Canvas(450 /* width */, 600 /* height */, g);#elif defined(MAKERFABS_TFT_TOUCH_3_5)
#define GFX_DEV_DEVICE MAKERFABS_TFT_TOUCH_3_5
Arduino_DataBus *bus new Arduino_ESP32SPI(33 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, 12 /* MISO */);
Arduino_GFX *gfx new Arduino_ILI9488_18bit(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */, false /* IPS */);#elif defined(MAKERFABS_ESP32_S3_TFT_4_0)
#define GFX_DEV_DEVICE MAKERFABS_ESP32_S3_TFT_4_0
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 1 /* CS */,12 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(45 /* DE */, 4 /* VSYNC */, 5 /* HSYNC */, 21 /* PCLK */,39 /* R0 */, 40 /* R1 */, 41 /* R2 */, 42 /* R3 */, 2 /* R4 */,0 /* G0 */, 9 /* G1 */, 14 /* G2 */, 47 /* G3 */, 48 /* G4 */, 3 /* G5 */,6 /* B0 */, 7 /* B1 */, 15 /* B2 */, 16 /* B3 */, 8 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type1_init_operations, sizeof(st7701_type1_init_operations));#elif defined(MAKERFABS_ESP32_S3_TFT_4_3_v1_3)
#define GFX_DEV_DEVICE MAKERFABS_ESP32_S3_TFT_4_3_v1_3
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 42 /* PCLK */,45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,0 /* hsync_polarity */, 40 /* hsync_front_porch */, 48 /* hsync_pulse_width */, 88 /* hsync_back_porch */,0 /* vsync_polarity */, 13 /* vsync_front_porch */, 3 /* vsync_pulse_width */, 32 /* vsync_back_porch */,1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);#elif defined(WT32_SC01)
#define GFX_DEV_DEVICE WT32_SC01
#define GFX_BL 23
Arduino_DataBus *bus new Arduino_ESP32SPI(21 /* DC */, 15 /* CS */, 14 /* SCK */, 13 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ST7796(bus, 22 /* RST */, 3 /* rotation */);#elif defined(WZ8048C050)
#define GFX_DEV_DEVICE WZ8048C050
#define GFX_BL 2
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(40 /* DE */, 41 /* VSYNC */, 39 /* HSYNC */, 0 /* PCLK */,45 /* R0 */, 48 /* R1 */, 47 /* R2 */, 21 /* R3 */, 14 /* R4 */,5 /* G0 */, 6 /* G1 */, 7 /* G2 */, 15 /* G3 */, 16 /* G4 */, 4 /* G5 */,8 /* B0 */, 3 /* B1 */, 46 /* B2 */, 9 /* B3 */, 1 /* B4 */,0 /* hsync_polarity */, 8 /* hsync_front_porch */, 4 /* hsync_pulse_width */, 43 /* hsync_back_porch */,0 /* vsync_polarity */, 8 /* vsync_front_porch */, 4 /* vsync_pulse_width */, 12 /* vsync_back_porch */,1 /* pclk_active_neg */, 16000000 /* prefer_speed */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);#elif defined(WAVESHARE_ESP32_S3_LCD_2_8)
#define GFX_DEV_DEVICE WAVESHARE_ESP32_S3_LCD_2_8
#define GFX_BL 5
Arduino_DataBus *bus new Arduino_HWSPI(41 /* DC */, 42 /* CS */, 40 /* SCK */, 45 /* MOSI */, 46 /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, 39 /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(WAVESHARE_RP2040_LCD_0_96)
#define GFX_DEV_DEVICE WAVESHARE_RP2040_LCD_0_96
#define GFX_BL 25
Arduino_DataBus *bus new Arduino_RPiPicoSPI(8 /* DC */, 9 /* CS */, 10 /* SCK */, 11 /* MOSI */, GFX_NOT_DEFINED /* MISO */, spi1 /* spi */);
Arduino_GFX *gfx new Arduino_ST7735(bus, 12 /* RST */, 0 /* rotation */, true /* IPS */, 80 /* width */, 160 /* height */, 26 /* col offset 1 */, 1 /* row offset 1 */, 26 /* col offset 2 */, 1 /* row offset 2 */);#elif defined(XIAO_SAMD21_ROUND_DISPLAY)
#define GFX_DEV_DEVICE XIAO_SAMD21_ROUND_DISPLAY
Arduino_DataBus *bus new Arduino_HWSPI(3 /* DC */, 1 /* CS */);
Arduino_GFX *gfx new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(XIAO_ESP32C3_ROUND_DISPLAY)
#define GFX_DEV_DEVICE XIAO_ESP32C3_ROUND_DISPLAY
Arduino_DataBus *bus new Arduino_ESP32SPI(5 /* DC */, 3 /* CS */, 8 /* SCK */, 10 /* MOSI */, 9 /* MISO */);
Arduino_GFX *gfx new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(XIAO_ESP32S3_ROUND_DISPLAY)
#define GFX_DEV_DEVICE XIAO_ESP32S3_ROUND_DISPLAY
Arduino_DataBus *bus new Arduino_ESP32SPI(4 /* DC */, 2 /* CS */, 7 /* SCK */, 9 /* MOSI */, 8 /* MISO */);
Arduino_GFX *gfx new Arduino_GC9A01(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(ZX2D10GE10R_V4848)
#define GFX_DEV_DEVICE ZX2D10GE10R_V4848
#define GFX_BL 38
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 21 /* CS */,47 /* SCK */, 41 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(39 /* DE */, 48 /* VSYNC */, 40 /* HSYNC */, 45 /* PCLK */,10 /* R0 */, 16 /* R1 */, 9 /* R2 */, 15 /* R3 */, 46 /* R4 */,8 /* G0 */, 13 /* G1 */, 18 /* G2 */, 12 /* G3 */, 11 /* G4 */, 17 /* G5 */,47 /* B0 */, 41 /* B1 */, 0 /* B2 */, 42 /* B3 */, 14 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 10 /* hsync_pulse_width */, 10 /* hsync_back_porch */,1 /* vsync_polarity */, 14 /* vsync_front_porch */, 2 /* vsync_pulse_width */, 12 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, st7701_type7_init_operations, sizeof(st7701_type7_init_operations));#elif defined(ZX3D50CE02S)
#define GFX_DEV_DEVICE ZX3D50CE02S
#define GFX_BL 45
Arduino_DataBus *bus new Arduino_ESP32LCD8(0 /* DC */, GFX_NOT_DEFINED /* CS */, 47 /* WR */, GFX_NOT_DEFINED /* RD */,9 /* D0 */, 46 /* D1 */, 3 /* D2 */, 8 /* D3 */, 18 /* D4 */, 17 /* D5 */, 16 /* D6 */, 15 /* D7 */);
Arduino_GFX *gfx new Arduino_ST7796(bus, 4 /* RST */, 0 /* rotation */, true /* IPS */);#elif defined(ZX3D95CE01S_AR)
#define GFX_DEV_DEVICE ZX3D95CE01S_AR
#define GFX_BL 45
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 0 /* CS */,10 /* SCK */, 9 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(13 /* DE */, 12 /* VSYNC */, 11 /* HSYNC */, 14 /* PCLK */,2 /* R0 */, 17 /* R1 */, 16 /* R2 */, 1 /* R3 */, 15 /* R4 */,41 /* G0 */, 46 /* G1 */, 3 /* G2 */, 42 /* G3 */, 8 /* G4 */, 18 /* G5 */,10 /* B0 */, 9 /* B1 */, 40 /* B2 */, 20 /* B3 */, 19 /* B4 */,1 /* hsync_polarity */, 10 /* hsync_front_porch */, 8 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 10 /* vsync_front_porch */, 8 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, GFX_NOT_DEFINED /* RST */, gc9503v_type1_init_operations, sizeof(gc9503v_type1_init_operations));#elif defined(ZX3D95CE01S_TR)
#define GFX_DEV_DEVICE ZX3D95CE01S_TR
#define GFX_BL 5
Arduino_DataBus *bus new Arduino_SWSPI(GFX_NOT_DEFINED /* DC */, 38 /* CS */,45 /* SCK or SCLK */, 48 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(40 /* DE */, 41 /* VSYNC */, 42 /* HSYNC */, 39 /* PCLK */,18 /* R0 */, 8 /* R1 */, 3 /* R2 */, 46 /* R3 */, 10 /* R4 */,14 /* G0 */, 13 /* G1 */, 12 /* G2 */, 11 /* G3 */, 16 /* G4 */, 17 /* G5 */,45 /* B0 */, 48 /* B1 */, 47 /* B2 */, 0 /* B3 */, 21 /* B4 */,1 /* hsync_polarity */, 8 /* hsync_front_porch */, 10 /* hsync_pulse_width */, 50 /* hsync_back_porch */,1 /* vsync_polarity */, 8 /* vsync_front_porch */, 10 /* vsync_pulse_width */, 20 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(480 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */,bus, 41 /* RST */, gc9503v_type1_init_operations, sizeof(gc9503v_type1_init_operations));#elif defined(ZX7D00CE01S)
#define GFX_DEV_DEVICE ZX7D00CE01S
#define GFX_BL 45
#define RGB_PANEL
Arduino_ESP32RGBPanel *rgbpanel new Arduino_ESP32RGBPanel(39 /* DE */, 38 /* VSYNC */, 5 /* HSYNC */, 9 /* PCLK */,10 /* R0 */, 11 /* R1 */, 12 /* R2 */, 13 /* R3 */, 14 /* R4 */,21 /* G0 */, 0 /* G1 */, 46 /* G2 */, 3 /* G3 */, 8 /* G4 */, 18 /* G5 */,17 /* B0 */, 16 /* B1 */, 15 /* B2 */, 7 /* B3 */, 6 /* B4 */,0 /* hsync_polarity */, 0 /* hsync_front_porch */, 210 /* hsync_pulse_width */, 30 /* hsync_back_porch */,0 /* vsync_polarity */, 0 /* vsync_front_porch */, 22 /* vsync_pulse_width */, 13 /* vsync_back_porch */);
Arduino_RGB_Display *gfx new Arduino_RGB_Display(800 /* width */, 480 /* height */, rgbpanel, 0 /* rotation */, true /* auto_flush */);/* Wio Terminal */
#elif defined(ARDUINO_ARCH_SAMD) defined(SEEED_GROVE_UI_WIRELESS)
#define GFX_DEV_DEVICE WIO_TERMINAL
// #define GFX_BL LCD_BACKLIGHT
Arduino_DataBus *bus new Arduino_HWSPI(LCD_DC /* DC */, LCD_SS_PIN /* CS */);
Arduino_GFX *gfx new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 1 /* rotation */);/* ESP32-S3-BOX */
#elif defined(ARDUINO_ESP32_S3_BOX)
#define GFX_DEV_DEVICE ARDUINO_ESP32_S3_BOX
#define GFX_BL 45
Arduino_DataBus *bus new Arduino_ESP32SPI(4 /* DC */, 5 /* CS */, 7 /* SCK */, 6 /* MOSI */, 0 /* MISO */);
Arduino_GFX *gfx new Arduino_ILI9342(bus, 48 /* RST */, 0 /* rotation */);/* M5Stack */
#elif defined(ARDUINO_M5Stack_Core_ESP32) || defined(ARDUINO_M5STACK_FIRE)
#define GFX_DEV_DEVICE ARDUINO_M5Stack_Core_ESP32
// #define GFX_BL 32
Arduino_DataBus *bus new Arduino_ESP32SPI(27 /* DC */, 14 /* CS */, SCK, MOSI, MISO);
Arduino_GFX *gfx new Arduino_ILI9342(bus, 33 /* RST */, 2 /* rotation */);#elif defined(ARDUINO_M5Stack_ATOMS3)
#define GFX_DEV_DEVICE ARDUINO_M5Stack_ATOMS3
#define GFX_BL 16
Arduino_DataBus *bus new Arduino_ESP32SPI(33 /* DC */, 15 /* CS */, 17 /* SCK */, 21 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_GC9107(bus, 34 /* RST */, 0 /* rotation */, true /* IPS */);/* Odroid-Go */
#elif defined(ARDUINO_ODROID_ESP32)
#define GFX_DEV_DEVICE ARDUINO_ODROID_ESP32
// #define GFX_BL 14
Arduino_DataBus *bus new Arduino_ESP32SPI(21 /* DC */, 5 /* CS */, SCK, MOSI, MISO);
Arduino_GFX *gfx new Arduino_ILI9341(bus, GFX_NOT_DEFINED /* RST */, 3 /* rotation */);
// Arduino_ST7789 *gfx new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 3 /* rotation */, true /* IPS */);/* LILYGO T-Watch */
#elif defined(ARDUINO_T) || defined(ARDUINO_TWATCH_BASE) || defined(ARDUINO_TWATCH_2020_V1) || defined(ARDUINO_TWATCH_2020_V2)
#define GFX_DEV_DEVICE ARDUINO_T_WATCH
#define GFX_BL 12
Arduino_DataBus *bus new Arduino_ESP32SPI(27 /* DC */, 5 /* CS */, 18 /* SCK */, 19 /* MOSI */, GFX_NOT_DEFINED /* MISO */);
Arduino_GFX *gfx new Arduino_ST7789(bus, GFX_NOT_DEFINED /* RST */, 0 /* rotation */, true /* IPS */, 240 /* width */, 240 /* height */, 0 /* col offset 1 */, 0 /* row offset 1 */, 0 /* col offset 2 */, 80 /* row offset 2 */);/* Waveshare RP2040-LCD-1.28 */
#elif defined(ARDUINO_WAVESHARE_RP2040_LCD_1_28)
#define GFX_DEV_DEVICE ARDUINO_WAVESHARE_RP2040_LCD_1_28
#define GFX_BL 25
Arduino_DataBus *bus new Arduino_RPiPicoSPI(8 /* DC */, 9 /* CS */, 10 /* SCK */, 11 /* MOSI */, 12 /* MISO */, spi1 /* spi */);
Arduino_GFX *gfx new Arduino_GC9A01(bus, 12 /* RST */, 0 /* rotation */, true /* IPS */);#endif
